100 Ohm Differential * 50 Ohm Single Ended Hand Held * Use with Articulating Manipulators
GigaProbes is a 30Ghz balanced odd mode 100 ohm differential Time-Domain Reflectometry (TDR) probe featuring Gold Plated Conductive Diamond probe tips that cuts through surface oxide that makes a solder like connection for repeatable TDR measurements.
This 30GHz TDR probe measures ODD/EVEN impedance profiles and can be used with the Tektronix DSA8200 TDR oscilloscope and all Tektronix legacy TDR oscilloscopes. With a typical differential launch discontinuity of 20mv and a fall-time of less than 30ps, these probes mask only 20 mills of the device under test. This small discontinuity mask becomes significant when characterizing IC packages where net lengths are very short.
The Signal-to-Signal pitch can be set to 0.4 to 1.27 mm (custom probes with wider pitch are available) using the special SMA Pitch Setting Wrench or customized using other tools supplied in the DVT30-1MM and DVT30-1MM-1 GigaProbes® accessory kit.
The DVT30-1MM GigaProbes™ interconnect analysis kit contains TWO differential 30Ghz Probes, four 24GHz SMA-SMA cables and many accessories (see page below). Acquire TDR/TDT waveforms and convert them to SDD11/21 S-parameters using the IConnect® MeasureXtractor SI software. Complete Time and Frequency domain analysis at a low cost.
DVT30-1MM-1 Single Probe GigaProbes® kit contains one 30 GHz Differential TDR probe. Contains Two 24GHz SMA-SMA cables and many accessories for Impedance and Failure Analysis Testing.
Each DVT30-1MM TDR/TD GigaProbes™ Kit includes:
Two - 30GHz 100 ohm differential TDR probes
Two - Easy-grip sleeves
One - SMA wrench with 0.8, 1.0, 1.27 mm probe tip pitch calibration holes
One - 5x Free Standing Microscope
One - 110 mm tweezers for fine pitch setting of probe tips
Four - right angle connectors
Two - 50 Ohm single ended conversion kit to include 2 SMA shorting caps and grounding strap
Two - cable wraps for easy cable management
Two - Micro Manipulator Adapter for the Tektronix PPM100 and PPM203 probe manipulators
One - Signal integrity resource disk and binder includes application notes and data sheets
The GigaProbes™ DVT30-1MM and DVT30-1MM-1 TDR/T Interconnect Development Kit comes with a full set of accessories for a complete interconnect analysis tool when used with the Tektronix DSA8200, TDR modules and the IConnect® signal integrity software. Probes are compatible with all Tektronix Legacy TDR oscilloscopes.
Choose the probe Kit that meets your measurement needs.
A 30 Ghz 100 Ohm Differential Hand Probe
Complete Interconnect Analysis and Development System from Tektronix. Components Displayed; Tektronix DSA8200, GigaProbes, 80EXX TDR Module, PPM100 Articulated Arm, IConnect Software, and External LCD Monitor
HANDS FREE PROBING: Direct Connect the GigaProbes to Tektronix TDR Modules
50 Ohm Probe: Accessories Included to Convert Probe to 30 GHz TDR Single Ended 50 Ohm Probe
Use Gigaprobes and IConnectMeasurextractor to create S-parameters, Extract S-Parameters from TDR/T waveforms and more.
Use GigaProbes™ and IConnect® for Interconnect Analysis
Using the GigaProbes™ to create TDR/TDT waveforms collected and port them into the Tektronix IConnect® software for efficient and easy signal integrity analysis of gigabit serial data interconnect analysis. Quickly measure insertion and return losses, reflections, eye diagrams, jitter, crosstalk, reflections, and ringing include signal path integrity analysis, impedance characterization and fault isolation.